Acrylic Fish Breeding Box - Aquarium Isolation Hatchery & Incubator for Baby Fish, Shrimp, Clownfish | Perfect for Safe Breeding, Quarantine & Acclimation in Home Aquariums

OK, this thing comes with no instructions and can be a pain to put together if you just go at it randomly. If you do it the following way though it's not bad. Take off all the protective coverings first:1. Attach left side panel to front panel and secure with bolster/screw/nut (see pictures in listing)2. Repeat for right side panel (be sure the flared part of the side panels that has the opening for the lid face the back)3. Fit bottom panel into the above.4. Add back panel and secure with bolster/screw/nut on one side only.5. Fit in internal dividers as desired.6. Secure other side of back panel with bolster/screw/nut and it should be solidly assembled7. Before fully tightening all the screws put top on if desired.8. Screw in hangers to the back and suction cups. (Note there are two screws longer than the rest and they're the ones to tighten it to the tank rim)Should only take 5-10 minutes total and no glue is needed.What I don't like about this product is the screws stick into the inter box fairly significantly and the pictures don't show that. I foresee this not being easy to clean once algae starts building up. Also, the internal separators can't be taken out easily; you have to partially undo the assembly. Something like the Eshopps Tanklimate is way better but also costs way more. I'm also concerned what the water flow will actually be like through the tiny openings. I was going to put some anemones in here but I don't think they're going to get enough water flow. The front and back panels have no openings for flow. The sides and bottom do but it's very narrow slits; small circular openings would be better for flow.Update: I'm taking off one more star because the suction cups don't work.It falls apart fast if your not careful. No instructions how to put it together. I had to use acrylic glue so it wouldn’t break apart everytime I tried to adjust the screws. The screws break easily. Once you know how to handle it you can make it work. The price is good.This is a set of clear acrylic parts cut on a CNC machine. Everything fits nicely and is fastened with the acrylic tabs and screws provided. The only tool needed is a philips screwdriver. The first step is to remove the protective film from all the pieces. Then lay them all out to determine the bottom, sides and top. put the edge tabs in the slots to make the basic box. A rubber band can be used to hold it together while the screws are added. There is no need for glue once all is tight. It is a good idea to pay attention to how the top opens, otherwise you may accidently put the ends on backwards. If you do, It is no big deal to flip the ends around.Just got this in and first there were 2 back pieces and no front piece. Second when putting in together everything is loose and the lid will fall off with the slightest jiggle. I fixed this by gluing all the pieces together. Doing it again I’d pay a little more for something better constructed.At first I was totally at a loss as to how to assemble. There are no instructions. Remove the plastic coating on both sides of the pieces. Put the cover and the middle divider aside while assembling. There are screws and holders that go through the side holes, see where they go first, by looking at the pictures carefully in the listing. Use the short screws. After all these are in place it holds together. It has a slight wiggle, but is so much better than the net ones.It came with no instructions. It came disassembled and if you’re not careful you break some of the plastic tabs and then you’re left with an unusable item. You face to put on your thinking cap for assembling it. I did break a little tab, but it still worked because I was careful with the rest of them. I would shell out more money for something of a higher quality. This just wasn’t it.Pretty decent, got to super glue it to hold. Also my package was missing the most important parts. The screws and suction cups ?Product is very fragile on its own and will likely not stay assembled without some sort of water/aquarium safe glue. I used superglue and 100% silicone aquarium sealant to ensure it stayed together. I used it for my aquarium bamboo.